"International Symposium on Single Crystal Diamond and Its Electronic Devices and the 4th China Vacuum High-Level Forum 2014" was held in Xi'an

Abstract On June 12-15, the International Symposium on Single Crystal Diamond and Its Electronic Devices and the Fourth Session of 2014 were co-sponsored by China Vacuum Society, Xi'an Jiaotong University, Shaanxi Science and Technology Association, China Vacuum Network and Shaanxi Vacuum Society. China Vacuum High Level Forum (SCDE...
June 12-15, International Symposium on Single Crystal Diamond and Its Electronic Devices and the 4th China 2014, jointly sponsored by China Vacuum Society, Xi'an Jiaotong University, Shaanxi Science and Technology Association, China Vacuum Network and Shaanxi Vacuum Society The Vacuum High-Level Forum (SCDE&2014CVF) was held in Xi'an. Song Xiaoping, Vice President of Xi'an Jiaotong University, Party Guangzhao, Vice Chairman of the Provincial Association of Science and Technology, and Liu Feng, China Vacuum Society attended the meeting.
The international symposium was chaired by Professor Wang Hongxing, a special expert of the National Thousand Talents Program of Xi'an Jiaotong University, Professor Nippon Jr. (Professor of the Japan Diamond Association) and Professor of the Shaanxi Vacuum Society. Waiting for the executive chairman of the conference.

meeting venue
The opening ceremony of the conference was presided over by Professor Wang Hongxing, and Song Xiaoping, Dang Guanglu and Liu Feng delivered speeches respectively.
Prof. Kawahara Kawahara of Waseda University in Japan, Professor Yoshio Yoshihiro of NIMS in Japan, Professor Sakai Shiro of Tokushima University in Japan, and Professor Zeng Yonghua of Taiwan's successful university respectively reported the latest research progress of their respective teams; Professor Wang Hongxing of Xi'an Jiaotong University introduced single crystal Recent advances in diamond growth, electronic device-level single crystal diamond epitaxial growth, diamond-based solar blind UV detection, and diamond-based power electronics. Jiangnan Researcher of Ningbo Institute of Materials, Chinese Academy of Sciences, Professor Li Chengming of Beijing University of Science and Technology, and Professor Liu Weiguo of Xi'an University of Technology also reported their latest research progress in single crystal diamond research. Researcher Lei Zhenlin from Shenyang Science and Technology Research Institute of the Chinese Academy of Sciences and Researcher Li Detian from 510 of the China Academy of Space Technology made wonderful reports on the current status and development trend of the large semiconductor industry and the application of mass spectrometers in space exploration.
Expert report
Finally, at the initiative of the delegates, 18 world-renowned universities and research institutions, including Xi'an Jiaotong University, Waseda University, and the National Materials Research Institute of Japan, initiated and established Panwa International Research and Development for Single Crystal Diamond and Its Electronic Devices. The Industry Alliance held a signing ceremony for the establishment of the alliance and established the first council. The secretariat of the Council is established as the permanent institution of the Alliance at Xi'an Jiaotong University. Professor Kawahara Tawan is the chairman of the board and Professor Wang Hongxing is the secretary general. Many units in the Chinese vacuum community participated in the alliance.
The conference provided an academic exchange platform for experts, scholars, technicians and Chinese vacuum entrepreneurs in the fields of single crystal diamond materials, electronic devices, diamond single crystal growth equipment, etc., and strengthened mutual exchanges between domestic and foreign industries. Understanding and cooperation are of great significance to promote the development of international single crystal diamond materials and their electronic components industry and related industries. The conference was a complete success.
More than 150 experts and scholars from different countries attended the international seminar.


Busbar Trunking System involves distribution of electrical power using set of copper/Aluminum bus bars enclosed in suitable encloser with high degree of protection against any ingress of foreign bodies.
Following are some advantages of Bus bar trunking system over normal cabling system:-
On-site installation times are reduced compared to hard-wired systems, thus leading to cost savings.
It provides increased flexibility in design and versatility with regard to future modifications.
Greater safety and peace of mind for specifiers, contractors and end-users.
Because of the simplicity of busbar, it is easy to estimate costs from the design/estimating stage through to installation on site. This is because the technical characteristics and price of each component are always known.
It is short sighted to compare the cost of busbar against that of a length of cable - and not the real cost of a cable installation to include multiple runs of cable, tray and fixing, let alone the protracted time and effort of pulling cables.
Distribution busbar distributes power along its length through tap-off points along the busbar at typically at 0.5 or 1 m centers. Tap-off units are plugged in along the length of the busbar to supply a load; this could be a sub distribution board or, in a factory, to individual machines. Tap-offs can normally be added or removed with busbar live, eliminating production down time.
Installed vertically the same systems can be used for rising-mains applications, with tap-offs feeding individual floors. Certified fire barriers are available at points where the busbar passes through a floor slab. Protection devices such as fuses, switchfuses or circuit breakers are located along the busbar run, reducing the need for large distribution boards and the large quantities of distribution cables running to and from installed equipment.
Very compact so provides space savings
Where aesthetics have to be considered, busbar trunking can be installed with natural galvanized, aluminum, or painted finish. Special colors to match switchboards or a specific color scheme are also available on request.
Busbar trunking has several key advantages over conventional forms of power distribution including: –
(a) Reduced, on site installation times when compared to hard-wired systems thus leading to cost savings.
(b) Increased flexibility in design and versatility with regard to future modifications.
(c) Increased safety features brought about by the use of high quality, manufactured components, which provide greater safety and peace of mind for specifiers, contractors and end-users.
Uneven distribution of current takes place where multiple runs of cables are used in parallel.
Busbar trunking has tap-off points at regular intervals along each length to allow power to be taken off and distributed to where it is needed. Because it is fully self-contained it needs only to be mechanically mounted and electrically connected to be operational.
For higher ratings of power distribution we need to have multiple runs of cable. In such conditions unbalanced distribution of current takes place and causing overheating of some cable. This is completely avoided in the BTS systems.
When multiple runs of cables are used it often leads to improper end connections thereby causing overheating of contacts, burning of cables ends, and is a major cause of fire. This is completely avoided in BTS systems.
Busbar versus Cables for Riser Applications:
Sr.no Issue Cable BUSBAR
1 Number of circuits One circuit per floor. Hence for a 20-floor building, you need 20 circuits. Just one circuit can cover all floors.

2 Main Switchboard Need 1 outgoing for each circuit. Hence 20 nos. MCCB outgoings. Higher cost and larger space requirement in electrical room Need only 1 outgoing for each riser. Lower cost and size of main panel.

3 Shaft Size Using 4 core cables, and considering 1 cable per feeder, you need 20 cables on the lowest floor. Large space required for cables/ Cable Tray. Typical size of 1600A riser is 185mm x 180mm. Leads to big savings on riser shaft size, and hence more usable floor area on every floor.

4 Fire & safety The high concentration of insulating materials used in cables and conductors involves a very high level of combustive energy. The volume of insulating materials used in trunking is reduced to a minimum so combustive energy is considerably lower than cables. The insulating materials used do not release corrosive or toxic gases in the event of a fire. Once the source of the fire is removed, these materials are extinguished in a few seconds so that theeffect of the fire is minimised.

5 Combustive Energy – see table enclosed 1600A – approx 60 kWh/sq.m 1600A – approx 5 kWh/sq.m.
Combustive energy is typically 80% –90% less than cables.

6 Future expansion If load on any floor exceeds initial plan, owner has to run an additional cable from a spare feeder on main board to that floor. By providing extra tap off slots on each floor at the design stage, owner only has to procure a tap off box and plug it in wherever additional load is required. As the plug in can be done live, there is no shut down required for any of the existing clients / circuits. Future Flexibility.

7 Fault withstand levels Limited by conductor size of each circuit. Much higher – typically a 1600 A riser has a fault withstand capability of 60 to 70 kA.Safer in an electrical fault.

8 Installation time Much longer Each riser on a 20-floor building can be installed in approximately 2 to 3 days.

9 Voltage drop High impedance if you choose cable size based on each floor current rating. Much lower impedance. Hencesubstantially lower voltage drop.

Busbar Trunking System

Busbar Trunking System,Compact Busbar,Aluminum Busbar,Lighting Busbar

Yangzhong Huaxin Power Equipment Co.,Ltd , http://www.huaxinbusbarchina.com